Basic Home Theater AV Set Up Guide – Hooking It All Up

| | 0 Comments

Friday, November 25, – If “eight speakers” means eight pairs of speakers, then we need to clear up the confusion. You don’t mention what receiver you have but I would hope it’s a fairly safe bet to conclude any modern “stereo” receiver has two pairs of speaker outputs wired internally to be in parallel. Very little that applies to a two channel stereo receiver transfers easily to a 5. In other words, with a two channel system, when only speaker “A” is engaged, the amplifier sees a load which represents one pair of speakers. When both “A” and “B” speaker outputs are engaged, the amplifier sees a parallel connection which would then show the amp approximatey half the impedance of the lower impedance speaker of the two pairs. There are also receivers being built today which do not allow both speaker ouptuts to be active simultaneously. In this case, when you engage one speaker switch, the other switch is automatically disengaged in order to provide protection to the amplifier. Therefore, if one set of speakers presents a nominal eight Ohm load while the second speaker set represents a nominal impedance of six Ohms, the amp will see a load of approximately three Ohms. Most modern receivers would be hard pressed to withstand a three ohm load for any length of time if the volume levels are being pushed.

Can I add 2 more speakers to my receiver?

Speakers Clint DeBoer Speaker Impedance Rating Explained That speaker impedance rating on your towers and bookshelf speakers is held up as a mystery—something strange and mystic, yet dangerous. The bottom line is that people are confused about speaker impedance. Speaker Impedance Defined I think the easiest way to define speaker impedance is to say that it is the resistance any speaker gives to the current and voltage being applied to it. In a nutshell, a loudspeaker is a big resister—a really cool one.

Hook up the television to the receiver. This is not absolutely necessary, as you won’t be using the television speakers anyway; but to make sure all components in your stereo system function as one, you’ll want to run an audio cable from the back of your television to the receiver.

In this article we look at some of the practical ways of wiring four speakers to each amplifier left and right. For example, it is normal to have your main HiFi amplifier in the lounge room. It is also common to want to have some speakers in the family room, outside patio or pool area and in the workshop or garage. If you need to connect just 2 pair of speakers to a HiFi stereo amplifier that is, 2 speakers to 1 amp , see my article on How to connect 2 speakers to 1 amplifier.

I have had many people over the years tell me it is easy to connect multiple speakers — all you have to do is wire the speakers in series. In the following diagrams I will only show the wiring for one side of a stereo amplifier, lets says the left side of the stereo. In reality this wiring needs to be duplicated for the right side speakers too. Four speakers wired in parallel This diagram shows how to wire four speakers in parallel. It is the same as wiring each speaker directly from the amplifier, like this: Wiring speakers in parallel is not a good way of connecting three, four or more HiFi speakers as it puts too much load on the amplifier as explained in earlier article Four speakers wired in series This diagram shows how to wire four speakers in series.

Again this is not a recommended way of wiring four speakers although it will work , nor is it very practical. Apart from the hassle of having to wire from one speaker to the next, if one wire is disconnected, then all speakers will stop working.

How to wire Four Speakers to One Amplifier

Here’s what to look for when shopping, along with the best computer speakers we’ve tested. But as you’ve probably noticed, that music only sounds as good as the system it’s playing through. Many PCs and Macs don’t come with very good speakers. And that’s to say nothing of the tiny built-in drivers found in most laptops.

This guide, very simply, walks through the basics of speaker placement, how to hook everything up, and how to change a few settings to really make your system shine. Throughout this article are links to other articles that go into more depth on each topic.

Weitere Informationen finden Sie auf unserer Seite der Datenschutzbestimmungen. Yep, all looks right to us. They are 8ohm with v30s and have parallel outs. If I understand this article correctly that will give me 4 ohms? The manual for the GM40 states to only use 8 or 16 ohm cabs…If I try hooking up both Mesa cabs, will I damage the head? Would it be at all possible to try hooking them up in serial though? I was also under the impression that I could connect my guitar to the amp head, and then wire the output of the amp head into my Fender Frontman R, thinking I would have the tone controls of both devices.

After reading this article I see that most amp heads are hooked up to cabinets. My question is, is it ever safe to hook an amp head to a regular amplifier? Are there safe combinations for this type of rig like the rules above for ohm ouput? I looked at the specs on the Fender Frontman and its list a bunch of different properties — Power Output, Poweramp Input, etc.

Why is connecting multiple speakers to one output bad?

Share on Facebook Insignia is the brand of televisions designed and sold by Best Buy. If you own an Insignia television you may want to connect a speaker system up to the TV. You can do this is very little time, without the aid from a technician or the Best Buy Geek Squad installation specialists. There is one audio output located towards the bottom of all the connection ports.

Feb 06,  · However, fact still stands, if you define power as the effect output on the amp according to ohms law, and that you stick to identically rated elements, more speakers will not produce more .

Though, I don’t know what type of speakers I can add without burning both the receiver or speakers because I don’t know about the ohms and watt laws. First of all, is my home theater a decent one? I love sound, I think I’m a potential audio-phile, and I want the best out of my home theater. I have a 7. I’ve read that front high have a specific effect for movies or so. But I noticed that my receiver also has a total of 9 spaces for speakers:

How to connect speakers to a computer

How do I mount a Play: Just make sure the mount is designed to support the weight of your speaker. How is Sonos different from Bluetooth speakers? Bluetooth is a short-range wireless solution that works by pairing a bluetooth speaker to a smart device to access music. Because your smart device and speaker need to be physically close to each other, the wireless range, expandability and control of a bluetooth connection can be limited.

Aug 25,  · You connect the turntable to the pre-amp, then the pre-amp to your Bluetooth speaker. That’s a bit clumsy and means more wires, so go for the first option if at all possible.

In some ways, thick, high-end wire can present MORE of a problem than the conventional skinnier stuff. More on that later. For the purposes of discussion we will use the term “amp” short for amplifier to refer to any receiver, integrated amp or power amp. This sheet is intended for solid state, transistorized sets. We’ll leave tubes out of this particular discussion. It is absolutely crucial that you use extra care in hooking up any solid state transistorized amp.

The first rule is to make sure the amp is turned off before connecting the speakers. Next make sure your wires are long enough to reach the speakers in one piece – rather than splicing numerous pieces together. When connecting the wire to the amp and speaker, make sure you have the proper “connectors” on the wire to mate with their respective terminals.

How to hook up 2 receivers for more power

Before trying to hook up your player, make sure it is plugged in and turns on when you press the “power” button. Usually a small light or welcome message appears when the DVD player is working correctly. There are at three common ways to connect a DVD player, and each needs a different cable to work. Your DVD player should come with all of the appropriate cords, but you need to check which connections your TV accepts as well.

The three most common are. HDMI connections are the highest quality connections and you only need one cord for both the audio and video.

If you keep adding speakers, at some point the speakers will demand more current than the amplifier can deliver, and it gives up its smoke and dies. Too many loads is .

Friday, October 24, – The receiver when used as a “pre-amp”, controls all the sound and any other processing that needs to be done from all you other components. This receiver will then send all that signal to a dedicated “power amplifier”, whose sole job is to amplify that signal and then send it to the speakers. Thus, leaving your receiver running cooler and more efficient, because it is not using it’s own power supply to run the speakers. You can use 2 receivers together but it will not really make much of a difference unless they are of significantly different power outputs.

If you are still using the speaker outputs on both unit, all you’ve done is have the ability to use more speakers. It’s still doing the same job and probably a little louder, just because there are more speakers. What you can do is, go to the rear of the weaker receiver and look for “pre-out” or “rec out” and connect it to the “input” jacks of the more powerful receiver.

It’s up to you where you want to hook this in, read your manual.

5% off your next item purchased on

Why Pair Bluetooth speakers? There are a few reasons you might want to create a pocket sized home theatre: You want a simple, easy set up 4.

Since I train multiple students at a time and often use 1-hr long DJ mixes to set paces for everyone, I connect my iPhone to an FM broadcast device (usually limited from a feet range). I additionally, I encourage trainees to use wireless devices such as nano shuffles, etc. that can pick up .

One thing I learned pretty early in life is that speakers are not meant to be wired together in a haphazard manner. In fact, whenever you plan to connect more than two speakers to a two-channel amplifier — or more than four speakers to a four-channel amp — there are a few things to consider, not the least of which is the amps ability to handle low-impedance loads. Ignoring the basics is like playing Russian roulette with your amplifier: If youre lucky, itll drive the speakers without incident; if youre not, the amp will fry.

The great thing about a multiple-speaker hookup is that once you master only two basic wiring procedures — “series” and “parallel” — the world is yours to conquer. When you know how many speakers youre going to use and the impedance driving capability of your amplifier, youll be able to select a wiring scheme that will deliver the best sonic and electrical results. In some cases, it may not be one procedure or the other but a combination of the two that works best. Speakers in Series The essence of series wiring is really quite simple: When speakers are connected in this fashion, load impedance increases — the more speakers, the higher the impedance.

The most common reason for wanting to raise impedance is to lower acoustical output, as in the case of rear-fill or center-channel speakers. Speaker output declines because the amplifiers power output decreases as the load impedance increases. While you can connect any number of speakers in series, try to keep the total equivalent-load impedance for each channel below 16 ohms, since most amps are not designed to handle higher loads.

Figure 1A demonstrates how to wire a pair of speakers in series. The positive output terminal from one channel of the amplifier is wired to the positive terminal of Speaker A, and the negative terminal of Speaker A is connected to the positive terminal of Speaker B.

UE Boom Party up with 50 or More speakers


Greetings! Would you like find a partner for sex? It is easy! Click here, free registration!